How to Change Colour in Crochet: A Clear Guide to Neat Stripes and Colourwork

Technique reference

Open the complete technique reference

Use this page for practice notes and troubleshooting, alongside the original lesson linked below.

Open the full lesson or reference →

Access: Free technique lesson or tutorial on the original publisher’s site.

Practice and troubleshooting checks
  1. 1Read the method
  2. 2Make a small sample
  3. 3Compare tension and result
  4. 4Record what worked

Original planning diagram. Follow the selected designer’s stitch instructions, counts and schematic.

Useful checks before you continue

If you notice this Try this check
The result differs from the example Check the exact stitch, terminology and yarn used before repeating it.
The fabric pulls or bunches Work a short sample slowly and compare the tension before and after the technique.
The method is hard to repeat Write down the sequence in your own words and keep the sample with the notes.

Learning how to change colour in crochet becomes much easier when you separate the stitch mechanics from the design decision. A clean switch can make stripes, colourwork, tapestry crochet, and mosaic crochet look intentional, while a rushed switch can leave bulky joins or uneven tension. The good news is that the same small habits work across many projects.

Start with the right tools and a clear colour plan

Gather the yarn colours you expect to use, a 5.5 mm hook if it suits your yarn, scissors, and an optional yarn needle. The source tutorial uses worsted-weight #4 yarn, but the method matters more than copying one material choice. Before you begin, look at the next few stitches and decide whether the new colour begins in the middle of a row, at the edge, or after a planned group of rows.

Keep the incoming strand close enough to reach comfortably, but do not pull it across the work before the stitch calls for it. That simple pause keeps the fabric relaxed and lets you see whether the transition will sit on the front or the wrong side. If a pattern gives a specific colour-change instruction, treat that instruction as the starting point and use the following checks to refine your tension.

How to change colour in crochet: two dependable ways

The first approach changes colour through the centre of a row. Work into the stitch as usual, then bring the new strand through the two loops or bars at the point where the transition belongs. This method is especially useful for small colour sections, graphghans, and situations where the previous yarn will be carried for a short distance.

The second approach changes colour on the last yarn over of a stitch. Work the stitch with the current colour until only that final yarn over remains, then use the new colour to complete it. This is the familiar method found in many written patterns and works well for stripes because the finished stitch already belongs visually to the next colour.

Whichever method you choose, keep the new strand in the same general tension as the old one. The join should not cinch the stitch smaller or leave a loose loop that will show once the following row is worked. Make one transition, inspect the fabric from the front, and adjust your hand position before continuing.

Carry yarn across a row without puckering

If the colour will return within a few stitches, cutting it may create more finishing work than necessary. Lay the unused strand across the top of the stitches and crochet over it as you work. Keep it slightly taut so it stays hidden, but never pull hard enough to draw the fabric inward. Puckering is usually a tension warning, not a reason to abandon the technique.

Carrying across a short distance works best when the float is concealed inside the fabric and the carried colour will not show through the front. Turn the work occasionally to inspect the reverse side, especially when using a light yarn beside a dark one. If the strand begins to form a long diagonal or feels easy to catch with a finger, stop carrying and plan a cleaner join.

Carry yarn up the side for tidy stripes

For stripes made with an even number of rows in each colour, carrying yarn up the side can save repeated cutting and weaving. Crochet over the tail in the first stitch, drop the unused colour, complete the planned rows, and pick that strand up again when it is needed. The edge can later be hidden in a seam or covered with a border.

This approach is particularly useful for blankets, scarves, garments, sweaters, and other striped projects with a stable side edge. Check the edge after every few rows: it should remain straight rather than drawing inward. If the carried yarn is visible from the front, loosen your handling slightly or change the finishing plan before the side becomes difficult to disguise.

Know when to cut yarn instead

Carrying is not automatically the neatest choice. Cut the strand when it will not be used again for many rows, when it would need to travel a long distance, or when it would show through the front of the fabric. Separate bobbins or small yarn balls can keep larger colourwork sections controlled without creating a long, exposed float.

When you cut, leave a useful tail and keep it toward the wrong side whenever possible. A yarn needle can help secure the end later, but do not weave it so tightly that the fabric loses its stretch. The goal is a transition that survives handling while still allowing the surrounding stitches to move naturally.

Quick answers for common colour-change questions

Which method is easiest for beginners?

Changing colour on the last yarn over is usually the clearest place to start because the new strand completes a stitch already in progress.

How can stripes have fewer yarn ends?

Carry the yarn up the side when the stripe rhythm and edge make that float easy to hide, then cover the edge with a seam or border if needed.

Can yarn be carried across a crochet project?

Yes, when the next colour change is nearby. Crochet over the strand with gentle, even tension and check that it does not show through the front.

Should yarn be cut after every colour change?

No. Cut only when carrying would create a long, visible, loose, or restrictive float; otherwise a short carried strand may be the cleaner option.

Finish with a small tension check

After the next colour change, spread the fabric gently and look at both sides before committing to several more rows. The transition should sit at the intended stitch, the carried yarn should not pucker the fabric, and the tails should remain manageable on the wrong side. With that quick check, colour changes become a repeatable part of your crochet rhythm rather than a moment of guesswork.

Keep a project record

Record the selected pattern and your own sample results. The designer’s measurements remain your reference.

  • Pattern and designer: ____________________
  • Technique and reference used: ____________________
  • Yarn / hook / sample size: ____________________
  • What changed and what to repeat next time: ____________________

Similar Posts